4000g ASTM Standard Geosynthetic Clay Liners Gcl for Landfill, Lake

• Customization: Available
• Width: 1-6m
• Length: 20-40m
• Model NO.: ASTM
• Sample: Free
• Standard: ASTM GB
• Application: Electrical Engineering, Roads & Railways & Airports Project, Water Conservancy Project
• Function: Reinforcement, Drainage
• Material: Polyester
• After-sales Service: More Than 10 Years
• Warranty: More Than 10 Years
• Color: White
• Classification: Bentonite
• Type: Bentonite
• Transport Package: Woven Geotextile + Steel Rolls
• Specification: 3000g-6500g
• Trademark: INNO
• Origin: China
• HS Code: 6815999000
• Production Capacity: 50000sqm/Per Day Depends on The Specification

Product Description

hot sale GCL for waste landfill geosynthetic clay liner with hdpe geomembrane

 Product introduction
Bentonite waterproof liner (GCL) is a new geosynthetic material. Taking natural sodium bentonite as material, bentonite particles are fixed between two layers of geotextile by special process to make bentonite waterproof blanket, which not only has all the characteristics of geotechnical materials, but also has excellent waterproof (seepage) performance.
O Product features

• It has excellent water swelling property and strong compactness;
• Durable waterproof performance, green environmental protection;

. With the functions of separation, reinforcement, protection and filtration, the construction is simple.

 

O Product specification
3OOOg/m²-6OOO0/m^z; Width: 3-6M



GCL Specification 

Notes
1 Bentonite property tests performed at a bentonite processing facility before shipment to INNO GCL production facilities.
2 Bentonite mass/area reported at 0 percent moisture content.
3 All tensile strength testing is performed in the machine direction using ASTM D 6768. All peel strength testing is performed using ASTM D 6496. Upon request, tensile and peel results can be reported per modified ASTM D 4632 using 4 inch grips.
4 Index flux and permeability testing with deaired distilled/deionized water at 80 psi (551kPa) cell pressure, 77 psi (531 kPa) headwater pressure and 75 psi (517 kPa) tailwater pressure. Reported value is equivalent to 925 gal/acre/day. This flux value is equivalent to a permeability of 5x10^-9 cm/sec for typical GCL thickness. Actual flux values vary with field condition pressures. The last 20 weekly values
prior the end of the production date of the supplied GCL may be provided.
5 Peak values measured at 200 psf (10 kPa) normal stress for a specimen hydrated for 48 hours. Site-specific materials, GCL products, and test conditions must be used to verify internal and interface strength of the proposed design.
 

MATERIAL PROPERTY	TEST METHOD	TEST FREQUENCY ft2(m2)	REQUIRED VALUES
Bentonite Swell Index^1	ASTM D 5890	1 per 50 tonnes	24 mL/2g min.
Bentonite Fluid Loss^1	ASTM D 5891	1 per 50 tonnes	18 mL max.
Bentonite Mass/Area^2	ASTM D 5993	40,000 ft^2 (4,000 m^2)	0.75 lb/ft^2 (3.6 kg/m^2) min
GCL Grab Strength^3	ASTM D 6768	200,000 ft^2 (20,000 m^2)	50 lbs/in (88 N/cm) MARV
GCL Peel Strength^3	ASTM D 6496	40,000 ft^2 (4,000 m^2)	3.5 lbs/in (6.1 N/cm) min
GCL Index Flux^4	ASTM D 5887	Weekly	1 x 10^-8 m^3/m^2/sec max
GCL Hydraulic Conductivity^4	ASTM D 5887	Weekly	5 x 10^-9 cm/sec max
GCL Hydrated Internal Shear Strength^5	ASTM D 5321 ASTM D 6243	Periodic	500 psf (24 kPa) typ @ 200 psf

GCL Production &  Packages 
Packaging & Delivery

Packaging Details:	packaged by black plastic woven geotextile
Delivery Detail:	7 days after deposit payment

 Installation Instructions


2 Before laying the bentonite waterproof blanket (GCL), there should be corresponding qualified acceptance documents for the preliminary project.
3 Before cutting the bentonite waterproof blanket (GCL), the relevant dimensions should be accurately measured, and then cut according to the actual terrain, and numbered piece by piece. The relevant information should be recorded on a special form. Laying bentonite waterproof blanket (GCL)
It must be dry and tidy, and no oil stains, splashed chemicals or chemical spots that damage the bentonite waterproof blanket (GCL) should be allowed on the surface.
4 Bentonite waterproof blanket (GCL) cannot be constructed in rainy weather and when there is water on the ground. To
5 In order to enhance the friction, the fiber of the waterproof pad is laid facing the base surface.
6 When laying the bentonite waterproof blanket (GCL), the joints should be minimized, and the raw materials should be saved as much as possible under the premise of ensuring the quality.
7 When laying the bottom surface, it should be overlapped in parallel, but not in parallel. The cloth surface should not be stretched too tightly or folded, and should be loosened appropriately and close to the ground;
8 When laying GCL when it encounters through parts, double-layer GCL waterproof pads should be laid within 500mm of the through objects. At the contact parts between GCL and the through objects, the upper and lower layers of GCL form a bell mouth, and the distance between the contact line and the through objects is at least greater than 50mm, GCL oblique mouth length is about 100mm, the gap between the two pads is filled with bentonite powder (it can also be filled with bentonite cement), and the joint between the upper layer of small waterproof pad and the lower layer of the entire waterproof pad should be glued and reworked. Fixed treatment
9 During laying, if the waterproof pad is damaged, apply a waterproof pad larger than 300mm around the damaged gap to cover it before fixing it;
10 When laying, if it rains, use plastic film material or rain-shielding material to quickly cover it. When the rain is heavy and the bentonite swells more than 300%, it should be re-laid;
11 When laying, it is strictly forbidden to put open flames or cigarette butts on any side of the waterproof pad.
Three, fixed
1 When laying, shop from top to bottom, and the direction of overlap is adapted to local conditions. Lay along the slope, and the joints must be parallel to the slope line and not intersect with the slope line.
2 In the deformed areas at the corners, the length of the joints should be as short as possible. At the toe of the slope or the place where the stress is concentrated, the horizontal joint distance must be greater than 1.5 meters. Except for special requirements, there should be no horizontal angle within 1.5 meters from the top of the slope or the stress concentration area on a slope with a slope greater than 1:6 Small 45°C seams.
3 When laying the Bentonite Waterproof Blanket (GCL), do not let stones, etc., which may damage the Bentonite Waterproof Blanket (GCL), or make the subsequent connection difficult, enter the Bentonite Waterproof Blanket (GCL) or under it.
4 On the slope surface, one end of the bentonite waterproof blanket (GCL) must be anchored, and then the coiled material must be put down along the slope surface to ensure that the bentonite waterproof blanket (GCL) remains tight. All bentonite waterproof blankets (GCL) must be pressed with sandbags, which will be used during laying and will be retained until the layer of material on top of laying.
5 After laying the bentonite waterproof blanket (GCL), it should be permanently anchored in time.
6 Sufficient temporary ballast (such as sandbags) is required during construction to prevent laying bentonite waterproof blanket (GCL)
Blowed by strong winds, the pressing materials used must be materials that will not damage the bentonite waterproof blanket (GCL), and retain them until the layer of material is laid.
7 While laying the bentonite waterproof blanket (GCL), the installation unit must take all necessary measures to prevent damage to the underlying material.
8 After installation, visually inspect the surface of all the bentonite waterproof blankets (GCL), mark and repair all the damaged areas, and make sure that there are no foreign substances, such as stones, that can cause damage to the paving surface. To
Four, connection



To get  more information pls contact us freely 

company Quality Inspection

Application:

·      Landfills	·      Mud Pits
·      Lagoons	·      Canals
·      Bund Lining	·      Tank Lining
·      Fish Farm Lining	·      Roof Lining
·      Waste Water Pits	·      Ponds and Reservoirs
·      Dams	·      Floating Covers
·      Vertical Cutoff Walls	·      Hydraulic Structure
·      Basement Lining	·      Drip Irrigation Ponds

Company Introduction 

Shandong Innovative Material Technology Co., Ltd.  covering an area of 196 mu; Registered address: No. 6399, East Tianqu Road, Dezhou; The registered capital is 260million yuan; Main business: focus on the research and development, production, construction, and sales service of high-end new geosynthetics.
The company has the world leading production line of polypropylene filament geotextile, domestic advanced staple fiber needle punched geotextile production, line, high density polyethylene geomembrane production line, composite geomembrane and composite geotextile production line. Polypropylene filament geotextile adopts the latest developed process equipment production line of Oeriikon and OBA company in Germany. The product is acid resistant, alkali resistant and corrosion resistant, which solves the problem of short service life of conventional products and of the adverse impact on engineering safety and environmental pollution after degradation. The world* s first 6.5m wide products enable the more convenient construction, the higher efficiency and great reduction of the usage cost.


Our company provides one-stop service. The goal is to let customers use least time to find the
required product with the best price.
Pre-sale service, our sales give the most suitable suggestions and recommendations according to the customer's situation. At the same time to answer various consulting questions about the product,and provide the best solution.
During the negotiation process, we use our professional attitude to guide our customers to get the
best value products and answer various consulting questions of the product, provide the best solution.
After-sale service, except the warranty service, we respond quickly to any kind of using problems or Support by online support 



Quality assurance
1.On a regular basis or as per your request,we entrust national testing agencies to conduct quality inspections
2.Strictly in accordance with the ISO9001-2008 international quality system standard,we monitor and manage the whole process throughout production,quality testing,and measurement to ensure product quality
3.  For quality-related construction delay or substandard construction(except for damage or losses due to customer's responsibility or irresistible natural disasters),we have refunding,replacement,and repair services.We will respond to customers' feedbacks on quality issues within 24 hours.
 
After-sales service
1.In order to provide customers with comprehensive technical support,we will provide technical and other related information upon request in a timely manner.
2.In required,we will appoint specialized technicians to the construction site to give technical trainings to construction people,and offer technical guidance throughout the whole construction process.
3.For damage due to shipment and delivery,after we receive the complaint,we will check the issure through provided pictures and videos.If our responsibility is confirmed,we wil offer free replacement. 
4.When the construction is completed,as your request,our technical staff may participate in the final acceptance.



We are online 24 Hours Pls feel free to contact us if any requirement